Home > Products > Sight Glass > Borosilicate Transparent Gauge Glass
Tel: +86-318-7906186    E-mail: info@cn-sealings.com

Borosilicate Transparent Gauge Glass

Transparent glasses are also manufactured from “extra-hard” high borosilicate glass. The surfaces on both sides are finely smooth and  ensure optimal transparency.

Now we have two kinds manufacturing technique:

  1. One is as same with reflex Gauge Glasses, use moulds to make the semi-finished products, afterwards, ground and polish the two side to ensure optimal transparency. By this manufacturing technique, the definition isn’t good.
  2. The other manufacturing technique is: At first, we manufacture 17mm thickness glass sheet, then cut the glass sheet according the detailed size and polish the side face for the smooth. This manufacturing technique glass is very clear, but the goods cost is higher.

It can be used with all media except steam at service conditions up to 8MPa and temperatures up to 430 °C.

Size:

  1. Type A:
    400x30x17mm(A11 ; AXI )                              370x30x17mm ( A10 ; AX )                                340x30x17mm (A9 ; AIX )          320x30x17mm (A8 ; AVIII )                               280x30x17mm ( A7 ; AVII )                                250x30x17mm (A6 ; AVI )
    220x30x17mm ( A5 ; AV )                                 190x30x17mm (A4 ; AIV)                                   165x30x17mm ( A3 ; AIII )          140x30x17mm ( A2 ; AII )                                 115x30x17mm ( A1 ; AI )                                    95x30x17mm  (A0)
  2. Type B:
    400x34x17mm(B11 ; BXI )                              370x34x17mm ( B10 ; BX )                                340x34x17mm ( B9 ; BIX )         320x34x17mm ( B8 ; BVIII )                              280x34x17mm ( B7 ; BVII )                                250x34x17mm ( B6 ; BVI )
    220x34x17mm ( B5 ; BV )                                 190x34x17mm ( B4 ; BIV )                                 165x34x17mm ( B3 ; BIII )         140x34x17mm ( B2 ; BII )                                 115x34x17mm ( B1 ; BI )                                    95x34x17mm  (B0)
  3. The other size is optional or according to the requirements of customers.

Installation instructions

Applications/ Use and Care                             

Please read the following information — it concerns your safety.

Each of our sight and gauge glass carefully manufactured and tested. It can only fill its duties safely and to your complete satisfaction if both the working conditions and information about its assembly and use are taken into account. We are pleased to provide you with some information on this page.

Fittings: You should always observe the manufacturer's instructions for assembling and changing sight and gauge glasses.

The basic fittings and flanges must satisfy the normal requirements for working under temperature and pressure conditions. It is particularly important that the flatness and freedom from distortion of the sealing surfaces can be guaranteed. These must satisfy at least the same requirements as are guaranteed for the sight and gauge glasses. The flatness should be checked when the sealing surfaces have been thoroughly and completely cleaned.

Never reuse a sight or gauge glass that has already been exposed to process conditions.

Sealing material: Always use new gaskets for assembly and use the sea-manufacturer of the fittings. These gaskets must also be flat and undamaged.

Mica protection  shields can be used to increase the working life of sight and gauge glasses and to allow them to be exposed to higher temperatures. However reflex glasses cannot be protected in this way. During assembly the glass must always be centred in the fitting in order to avoid a glass-metal contact. The correct sequence must always be observed when assembling the glass, gasket and mica protection shield.

Sequence for Tightening Cover Bolts/ Nuts
Tightening the Fitting screws:
First tighten
The clean and greased nuts by hand.Then tighten them In the sequence shown in the Diagram Always start in the middle and then work outwards on alternate sides. Finally, tighten the flange bolts or nuts to the exact torque given by the manufacturer.

During operating processes  never try to clean the glass by mechanical means,never tighten up the nuts and bolts of the fitting and never perform other work on the fitting.

Transport packing is used to protect the glasses. Please leave the glass in packing until they are required for use and avoid contact with other glass or metal components.

Sight and gauge glasses which are scratched, chipped, pitted or any other surface damage exist, should never be used.

Sight and gauge glass condition

Checks should be carried out regularly; when used in new and unknown processes daily. Keep maintenance records and replace the glasses on a regular basis. Look for damage,scratches and loss of substance.

Cleaning the glasses: please only use commercially available glass cleaning agents to clean the glasses. Never use wire brushes, metal scrapers, or other sharp-edged items Which could scratch the glass and make it unusable. Opaque and rough glasses which cannot be cleaned with simple cleaning agents should be replaced.

Our aim is to inform and advise our customers. Nevertheless,general values obtained from experience and test results simply cannot be applied to particular and specific applications. Too many factors which we cannot influence play a role. We must therefore ask you to appreciate that no claims can be made which may arise as a result of any advice we may have provided. You are responsive to property care for and maintain the sight glasses.

If you need to consult the price, please contact the business department by e-mail:
Fuyuan will service for you !
E-mail: info@cn-sealings.com / info@tongfengindustry.com
Tel: +86-318-7906186
Fax: +86-318-7080093

When you contact us, please provide your detail requirements. That will help us give you a valid quotation.

Copyright © 2014 Hebei Fuyuan Sealing Materials Co., Ltd. ADD: 1-1-901, Fuxingyuan, 161# Ronghua Street, Hengshui City, Hebei, China.
Zip Code: 053000 Tel: +86-318-7906186 Fax: +86-318-7080093 E-mail: info@cn-sealings.com / info@tongfengindustry.com
URL: http://www.cn-sealings.com (Global) / http://www.asbestos-joint.com (CN/EN))

Back to Top